DataSheet.fr

PDF ISL6363 Fiche technique - Intersil Corporation

Numéro de référence ISL6363
Description Multiphase PWM Regulator
Fabricant Intersil Corporation 
Logo Intersil Corporation Logo 

32 Pages
		

No Preview Available !

ISL6363 Datasheet, Description
Multiphase PWM Regulator for VR12™ Desktop CPUs
ISL6363
Fully compliant with VR12™ specifications, the ISL6363
provides a complete solution for microprocessor core and
graphics power supplies. It provides two Voltage Regulators
(VRs) with three integrated gate drivers. The first output (VR1)
can be configured as a 4, 3, 2 or 1-phase VR while the second
output (VR2) is a 1-phase VR. The two VRs share a serial control
bus to communicate with the CPU and achieve lower cost and
smaller board areacomparedwith a two-chip approach.
Based on Intersil’s Robust Ripple Regulator R3 Technology™,
the PWM modulator, compared to traditional modulators, has
faster transient settling time, variable switching frequency
during load transients and has improved light load efficiency
with its ability to automatically change switching frequency.
The ISL6363 has several other key features. Both outputs
support DCR current sensing with a single NTC thermistor for
DCR temperature compensation or accurate resistor current
sensing. Both outputs come with remote voltage sensing,
programmable VBOOT voltage, serial bus address, IMAX, TMAX,
adjustable switching frequency, OC protection and separate
power-good indicators. To reduce output capacitors, the
ISL6363 also has an additional compensation function for
PS1/2 mode and high frequency load transient compensation.
Features
• Serial Data Bus (SVID)
•D ual Outputs:
- Configurable 4, 3, 2 or 1-phase for the 1st Output with 2
Integrated Gate Drivers
- 1-phase for the 2nd Output with Integrated Gate Driver
• Precision Core Voltage Regulation
- 0.5% System Accuracy Over-Temperature
- Enhanced Load Line Accuracy
• PS2 Compensation and High Frequency Load Transient
Compensation
• Differential Remote Voltage Sensing
• Lossless Inductor DCR Current Sensing
•P rogrammable VBOOT Voltage at Start-up
• Resistor Programmable Address, IMAX, TMAX for Both
Outputs
• Adaptive Body Diode Conduction Time Reduction
Applications
•V R12 Desktop Computers
Related Literature
• ISL6363EVAL1Z User Guide
VCORE
50mV/DIV
COMP
1V/DIV
2µs/DIV
65A STEP LOAD
1V/DIV
FIGURE 1. FAST TRANSIENT RESPONSE
1.15
1.10
1.05
1.00
0.95
1.7mLOADLINE
1.1V - PS1
1.1V - PS0
0.90
0 5 101 5 20 253 03 5 40 45 50 55 60 65 70 75 80 85
IOUT (A)
FIGURE 2. ACCURATE LOADLINE, VCORE vs IOUT
September 29, 2011
FN6898.0
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Copyright Intersil Americas Inc. 2011. All Rights Reserved
Intersil (and design) and R3 Technology are trademarks owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
http://www.Datasheet4U.com
ISL6363 Fiche technique
ISL6363
Pin Descriptions (Continued)
ISL6363
9
10
11
12
13
14
15
16
17
18
19, 20, 21
22
23
24
25
26
27
28, 29
30
31
32
33
34
35
36
37
38
39
40
SYMBOL
ISEN4
VSEN
PSICOMP
RTN
FB
COMP
VW
NTC
IMON
VR_ON
SDA,
ALERT#,
SCLK
PGOODG
IMONG
VWG
COMPG
FBG
RTNG
ISUMPG,
ISUMNG
NTCG
VR_HOT#
PVCCG
LGATEG
BOOTG
UGATEG
PHASEG
PWM4
PWM3
PHASE2
UGATE2
DESCRIPTION
VR1 phase 4 current sense input pin for phase current balancing.
VR1 remote core voltage sense input.
This pin is used for improving transient response in PS2/3 mode of VR1 by switching in an additional type 3 compensation
network to improve system gain and phase margin. Connect a resistor and capacitor from this pin to the output of VR1 near
the feedback compensation network.
VR1 remote voltage sensing return input. Connect this pin to the remote ground sensing location.
Inverting input of the error amplifier for VR1.
This is a dual function pin. This pin is the output of the error amplifier for VR1. A resistor connected from this pin to GND
programs IMAX for VR1 and VBOOT for both VR1 and VR2. Refer to Table 7 on page 28.
A resistor from this pin to COMP programs the PWM switching frequency for VR1.
One of the thermistor network inputs to the thermal monitoring circuit used to control the VR_HOT# signal. Use this pin to
monitor the temperature of VR1. Place the NTC close to the desired thermal detection point on the PCB.
Current monitoring output pin for VR1. The current sense signal from ISUMN and ISUMP is output on this pin to generate a
voltage proportional to the output current of VR1.
Enable input signal for the controller. A high level logic signal on this pin enables the controller and initiates soft-start for VR1
and VR2.
Data, alert and clock signal for the SVID communication bus between the CPU and VR1 and VR2.
Power-good open-drain output indicating when VR2 is able to supply a regulated voltage. Pull-up externally with a 680
resistor to +5V or 1.0kto 3.3V.
Current monitoring output pin for VR2. The current sense signal from ISUMNG and ISUMPG is output on this pin to generate
a voltage proportional to the output current of VR2.
A resistor from this pin to COMPG programs the PWM switching frequency for VR1.
This is a dual function pin. This pin is the output of the error amplifier for VR2. A resistor connected from this pin to GND
programs IMAX for VR2 and TMAX for both VR1 and VR2. Refer to Table 8 on page 28.
Inverting input of the error amplifier for VR2.
VR2 remote voltage sensing return input. Connect this pin to the remote ground sensing location.
VR2 current sense input pin for current monitoring, droop current and overcurrent detection.
One of the thermistor network inputs to the thermal monitoring circuit used to control the VR_HOT# signal. Use this pin to
monitor the temperature of VR2. Place the NTC close to the desired thermal detection point on the PCB.
Open drain thermal overload output indicator.
Input voltage bias for the internal gate driver for VR2. Connect +12V to this pin. Decouple with at least a 1µF MLCC capacitor
and place it as close to the pin as possible.
Output of the VR2 low-side MOSFET gate driver. Connect this pin to the gate of the VR2 low-side MOSFET.
Connect a MLCC capacitor from this pin to the PHASEG pin. The boot capacitor is charged through an internal boot diode
connected from the PVCCG pin to the BOOTG pin.
Output of the VR2 high-side MOSFET gate drive. Connect this pin to the gate of the VR2 high-side MOSFET.
Current return path for the VR2 high-side MOSFET gate driver. Connect this pin to the node connecting the source of the
high-side MOSFET, the drain of the low-side MOSFET and the output inductor of VR2.
PWM output for phase 4 of VR1. When PWM4 is pulled to +5V VCC, the controller will disable phase 4 of VR1.
PWM output for phase 3 of VR1. When PWM3 is pulled to +5V VCC, the controller will disable phase 3 of VR1.
Current return path for the VR1 phase 2 high-side MOSFET gate driver. Connect this pin to the node connecting the source of
the high-side MOSFET, the drain of the low-side MOSFET and the output inductor of phase 2.
Output of the VR1 phase 2 high-side MOSFET gate drive. Connect this pin to the gate of the high-side MOSFET of phase 2.
3 FN6898.0
September 29, 2011

3 Page

ISL6363 pdf
ISL6363
Simplified Application Circuit
+5V
Vin +12V
Rntcg
oC
PGOODG
Rfsetg
Rprog2
VCCSENSEG
VSSSENSEG
Rdroopg
IMONG
SDA
ALERT#
SCLK
Rscomp
Raddr
Rntc
oC
VR_HOT#
PGOOD
VR_ON
Rfset
Rprog1
VCCSENSE
VSSSENSE
Rdroop
IMON
VCC PVCC
NTCG
PGOODG
PVCCG
BOOTG
UGATEG
PHASEG
VWG
LGATEG
COMPG
ISUMPG
ISUMNG
FBG
RTNG
PWM4
IMONG
ISL6363
SDA
ALERT#
SCLK
SCOMP
ADDR
NTC
PWM3
BOOT2
UGATE2
PHASE2
VR_HOT#
PGOOD
VR_ON
VW
LGATE2
BOOT1
UGATE1
PHASE1
COMP
LGATE1
ISUMP
FB
PSICOMP
ISUMN
VSEN
RTN
IMON
ISEN4
ISEN3
ISEN2
GND ISEN1
Rsumg
Cng
Rig
Rng
oC
Vsumng
+12V Cvsumng
VCC
UGATE
PVCC PHASE
ISL6622
PWM
BOOT
LGATE
GND
+12V
VCC
UGATE
PVCC PHASE
ISL6622
PWM
BOOT
LGATE
GND
Vin
+12V
Rsum4
Rsum3
Rn
Cn oC
Rsum2
Rsum1
Ri Vsumn
Cvsumv
Cisen1 Cisen2 Cisen3Cisen4 Risen4
Risen3
Risen2
Risen1
6
LG GX Vcore
L4
L3
L2 CPU Vcore
L1
FN6898.0
September 29, 2011

6페이지



Constitution32 Pages
Télécharger[ ISL6363.PDF ]

Liens de partage


Fiche technique recommandé

RéférenceDescriptionFabricant
ISL6363Multiphase PWM RegulatorIntersil Corporation
Intersil Corporation
ISL6364Dual 4-Phase + 1-Phase PWM ControllerIntersil Corporation
Intersil Corporation
ISL6366Dual 6-Phase + 1-Phase PWM ControllerIntersil Corporation
Intersil Corporation
ISL6367HGreen Hybrid Digital Dual 6-Phase 1-Phase PWM ControllerIntersil Corporation
Intersil Corporation

RéférenceDescriptionFabricant
H6060The H6060 is a monolithic low-power CMOS device combining a programmable timer and a series of voltage comparators on the same chip.EM Microelectronic - MARIN SA
EM Microelectronic - MARIN SA
IT8772EThe IT8772E is a highly integrated Super I/O using the Low Pin Count Interface. It provides the most commonly used legacy Super I/O functionality plus the latest Environment Control initiatives, including H/W Monitor and Fan Speed Controller.ITE
ITE

Un datasheet est un document fourni par le constructeur du composant, où figurent toutes les données techniques sur le produit: puissance dissipée, courant maximal, tension de seuil, tension de claquage, température de stockage, etc. Ils sont en général fournis gratuitement, et se présentent très régulièrement sous la forme d'un document pdf.


www.DataSheet.fr    |   2018   |  Contactez-nous    |   Recherche